Industrial
Monitor- Monochrome CRT Display
14"
Open Frame or Kit Monitor
LP 14 Series
(See table below for model numbers)
|
|
|
|
|
|
This Omni Vision
monitor is offered in an open frame chassis or as a kit version product
for applications where a small display is required and the input signal
can be composite video or TTL or analog video with TTL sync. This low
power CRT module is a great solution. This 14" CRT provides great viewing
angles and higher brightness levels. The main circuit board is made of
industrial grade epoxy/fiber glass reinforced material with an FR4 rating.
Industrial CRT Replacement Monitor FEATURES
All circuitry is on a single, double sided, plated through PCB.
All controls are easily accessible from the top of monitor.
The video display is stabilized through the use of a voltage
controlled, temperature compensated feedback to synchronized free
run oscillator.
Electronic horizontal video centering.
Geometric distortion - within 2 % EIS Standard Dot/Ball Chart
or variation between adjacent characters not more than 10 % in alpha
numeric display applications
High Voltage - Over 10 kV at 50 microamperes of beam current
with no more than 0.5 kV variation from zero beam to 100 microamperes
beam current |
|
|
|
Industrial CRT Replacement Monitor SPECIFICATIONS |
|
|
CRT
size: |
14"
|
Phosphor: |
White
P4 standard. Green and Amber optional. |
Display
size: |
93
sq. in. max.
|
Scanning:
|
Interlaced
& Non-interlaced |
Horizontal
frequencies: |
15
to 35.5 kHz ± 500 Hz |
Vertical
frequencies: |
50
or 60 Hz |
Video
Response: |
From
20 to 26 MHz
|
Maximum
Resolution: |
800
X 600 @ 56 Hz |
Display
Color: |
Unlimited
Gray Scale |
Agency
Approvals: |
UL,
cUL, TÜV |
Agency
Compliance: |
FDA,
CE, FCC |
Dimensions
(HxWxD): |
See
mechanical drawing:94-015 |
Weight
(approx.): |
Depends
on product version: chassis or kit . |
|
|
|
Industrial CRT Replacement Monitor ADDITIONAL
SPECIFICATIONS
|
TTL
Signals
|
Signal
|
Positive
polarity |
+
2.5 v to 5.0 v |
Video
|
Input
Impedance Bandwidth |
470
ohms Within 3 dB from 10 Hz to 26 kHz |
Vertical
|
Input
Impedance Typical Signal |
Greater
than 1k Ohms 180 micro seconds |
Horizontal
|
Input
Impedance Typical Signal |
Greater
than 6k Ohms 2.5 to 8 micro seconds |
Composite
Video
|
Signal
|
Positive
video - negative sync |
0.7
v to 1.8 v peak to peak composite |
|
Input
Impedance Bandwidth |
75
Ohms Within 3 dB from 10 Hz to 26 kHz |
Industrial CRT Replacement Monitor GENERAL
INFORMATION
On
board service controls Brightness, Contrast, Focus Horizontal [Size, Centering,
Hold],
Vertical [Size,
Centering, and Linearity]
Optional remote brightness interface available
Input signal type standard - Analog Video - 0 to 0.7 volts
Horizontal
& Vertical Sync Signals - TTL level 0 to 5 volts
Signal Connectors - Standard card edge connector
Input Power - Standard +12 vdc @ 1.5 A (typical)
Input Power Connector - Standard card edge connection
Optional - Remote AC Power Input - 100-240 VAC auto ranging (47-63
Hz)
Temperature - Operating from 0 to +55 ° C
-Storage
from -20 to +65 ° C
Industrial CRT Replacement Monitor ORDERING
INFORMATION
When ordering, compile model number from the options listed below. Example:
LP14-18-G-2A-P4 specifies Model LP12 with 18 kHz frequency, NTSC, factory
assigned number and white phosphor tube.
Frequency
Horizontal
(kHz)
|
Signal
|
Chassis
|
Kit
|
Factory
Assigned
|
Phosphor
Color
|
15
18
21
24
31
35
48
|
Composite
Video
|
G
NTSC or PAL
|
G
NTSC or PAL
|
1-9
or
A-Z
or
combination
|
P4
White
|
TTL
|
E
Std TTL or Analog Video w/TTL sync.
|
E
Std TTL or Analog Video w/TTL sync.
|
P31
Green
|
LA
Amber
|
|
|
|
Industrial CRT Replacement Monitor DIMENSIONS
Drawing
94-015 for Industrial CRT Replacement Monitor Chassis Model LP14 |
 |
| |