Industrial
Monochrome CRT Monitor
9"
& 12" Open Frame Replacement Monitor
LP09 & LP12 Series
(See table below for model numbers)
|
Yoke
Mount Version TTL Input (15 or 18 kHz) Signal Replacement Monitor
Model - LP0915LG4- Model - LP0918LG4- Model - LP1215LG4- Model - LP0918LG4- |
 |
9" CRT model shown
This family of Omni Vision monitors is offer "chassis less" design where the main PCB is mount around the neck of the CRT. No need to worry about where to mount the circuit board; just mount the CRT and connect the signal and power to the unit thru a 10-pin card edge connector. The main circuit board is made of an industrial grade epoxy/fiber glass reinforced material with an FR4 rating.
|
FEATURES • All circuitry is on a single, double sided, plated through PCB. • All controls are easily accessible from the top of monitor. • The video display is stabilized through the use of a voltage controlled, temperature compensated feedback to synchronized free run oscillator. • Electronic horizontal video centering. • Geometric distortion - within 2 % EIS Standard Dot/Ball Chart or variation between adjacent characters not more than 10 % in alpha numeric display applications • High Voltage - Over 8 kV at 50 microamperes of beam current with no more than 0.5 kV variation from zero beam to 100 microamperes beam current |
|
Omni
Vision Model Number
|
LP0915LG4-(P4.
P31 or LA)
LP0918LG4-(P4. P31 or LA) |
LP1215LG4-(P4.
P31 or LA) |
| CRT Size |
9"
|
12"
|
| Phosphor: |
White
P4, Green P31or Amber LA
|
White
P4, Green P31or Amber LA
|
| Scanning: |
Non-interlaced
|
Non-interlaced
|
| Resolution ( Typ) |
At
15 kHz—640 x 240
At 18 kHz—720 x 288 |
At
15 kHz—640 x 240
At 18 kHz—720 x 288 |
| Horizontal frequency: |
15or
18.4 kHz ± 500 Hz
|
15or
18.4 kHz ± 500 Hz
|
| Vertical frequency: |
50
or 60 Hz
|
50 or 60 Hz
|
| Video Response: |
To
20 MHz
|
To 20 MHz |
| Viewing Area : |
35
sq. in. max.
|
55
sq. in. max.
|
|
Enhanced
Video Input
|
To
10 MHz
|
To
10 MHz
|
| Agency Approvals: |
UL,
cUL, TÜV
|
UL,
cUL, TÜV
|
| Agency Compliance: |
FDA,
CE, FCC
|
FDA,
CE, FCC
|
| Dimensions (HxWxD): |
See
mechanical drawing 94-007
|
See
mechanical drawing 94-007
|
| Weight (approx.): |
3.5
lbs.
|
3.5
lbs.
|
|
ADDITIONAL
SPECIFICATIONS
|
||
|
TTL
Signals
|
||
| Signal | Positive polarity | + 2.5 v to 5.0 v |
| Video | Input Impedance Bandwidth | 470 ohms Within 3 dB from 10 Hz to 26 MHz |
| Vertical | Input Impedance Typical Signal | Greater than 1k Ohms 180 micro seconds |
| Horizontal | Input Impedance Typical Signal | Greater than 6k Ohms 2.5 to 8 micro seconds |
GENERAL
INFORMATION
- On board
service controls Brightness, Contrast, Focus Horizontal [Size, Centering,
Hold],
Vertical [Size, Centering, and Linearity] - Optional remote brightness interface available
- Input
signal type standard - Analog Video - 0 to 0.7 volts
Horizontal & Vertical Sync Signals - TTL level 0 to 5 volts - Signal Connectors - Standard card edge connector
- Input Power - Standard +12 vdc @ 1.5 A (typical)
- Input Power Connector - Standard card edge connection
- Temperature
- Operating from 0 to +55 ° C
-Storage from -20 to +65 ° C
| PRINTING The following PDF files may be used for printing the Data Sheet |
|||||||||||
 |
|||||||||||
|
QUESTIONS?
CALL 630.893.1720
|
|||||||||||