Industrial
Monochrome CRT Monitor
6"
Open Frame or Kit Monitor
LP 06 Series
(See table below for model numbers)
This Omni Vision monitor is offered in an open frame chassis or as a kit version product for applications where a small display is required and the input signal can be composite video or TTL or analog video with TTL sync. This low power CRT module is a great solution. The flat face 6" CRT provides great viewing angles and higher brightness levels. The main circuit board is made of industrial grade epoxy/fiber glass reinforced material with an FR4 rating.
|
FEATURES • All circuitry is on a single, double sided, plated through PCB. • All controls are easily accessible from the top of monitor. • The video display is stabilized through the use of a voltage controlled, temperature compensated feedback to synchronized free run oscillator. • Electronic horizontal video centering. • Geometric distortion - within 2 % EIS Standard Dot/Ball Chart or variation between adjacent characters not more than 10 % in alpha numeric display applications • High Voltage - Over 8 kV at 50 microamperes of beam current with no more than 0.5 kV variation from zero beam to 100 microamperes beam current |
| CRT size: |
6" |
| Phosphor: | Green P31, standard. White optional. |
| Display size: |
20 square inches, max. |
| Scanning: | Interlaced & Non-interlaced |
| Horizontal frequencies: | 15 to 31.4 kHz ± 500 Hz |
| Vertical frequencies: | 50 or 60 Hz |
| Video Response: |
From 20 to 26 MHz |
| Maximum Resolution: | 640 x 480 @ 60 Hz |
| Display Color: | Unlimited Gray Scale |
| Agency Approvals: | UL, cUL, TÜV |
| Agency Compliance: | FDA, CE, FCC |
| Dimensions (HxWxD): | See mechanical drawing 94-007 |
| Weight (approx.): | Depends on product version: chassis or kit . |
|
ADDITIONAL
SPECIFICATIONS
|
||
|
TTL
Signals
|
||
| Signal | Positive polarity | + 2.5 v to 5.0 v |
| Video | Input Impedance Bandwidth | 470 ohms Within 3 dB from 10 Hz to 26 kHz |
| Vertical | Input Impedance Typical Signal | Greater than 1k Ohms 180 micro seconds |
| Horizontal | Input Impedance Typical Signal | Greater than 6k Ohms 2.5 to 8 micro seconds |
|
Composite
Video
|
||
| Signal | Positive video - negative sync | 0.7 v to 1.8 v peak to peak composite |
| Input Impedance Bandwidth | 75 Ohms Within 3 dB from 10 Hz to 26 kHz | |
GENERAL
INFORMATION
• On
board service controls Brightness, Contrast, Focus Horizontal [Size, Centering,
Hold],
Vertical [Size,
Centering, and Linearity]
• Optional remote brightness interface available
• Input signal type standard - Analog Video - 0 to 0.7 volts
Horizontal
& Vertical Sync Signals - TTL level 0 to 5 volts
• Signal Connectors - Standard card edge connector
• Input Power - Standard +12 vdc @ 1.5 A (typical)
• Input Power Connector - Standard card edge connection
• Temperature - Operating from 0 to +55 ° C
-Storage
from -20 to +65 ° C
ORDERING
INFORMATION
When ordering, compile model number from the options listed below. Example:
LP06-15-G-2A-P31 specifies Model LP06 with 15 kHz frequency, NTSC, factory
assigned number and green phosphor tube.
|
LP06-XX-Y-ZZ-?
|
|
Frequency
Horizontal (kHz) |
Signals
|
Chassis
|
Kit
|
Factory
Assigned
|
Phosphor
Color
|
|
15
19
31
|
Composite
Video
|
G
NTSC or PAL
|
G
NTSC or PAL
|
1-9
or
A-Z
or
combination
|
P4
White
|
|
TTL
|
E
Std TTL or Analog Video w/TTL sync.
|
E
Std TTL or Analog Video w/TTL sync.
|
P31
Green
|
||
| DIMENSIONS Drawing 94-007 for Chassis Model LP06 |
 |
| PRINTING The following PDF files may be used for printing A-size drawings 94-007 or the Data Sheet. |
|||||||||||
 |
|||||||||||
|
QUESTIONS
CALL 630.893.1720
|
|||||||||||